
Inside Work Space: 19"d x 24"w x 24"h
Outside Dimensions: 23"d x 25.5"w x 66"h
Shipping Weight: 330lbs.
The standard unit is 110 volt, 15 amp; also available as 220 volt, 50 hz.
This 50 lb., ASME-certified pressure vessel houses the abrasive. It automatically filters out debris to prevent clogging. Our exclusive 45 degree angle design allows for a more consistent sandflow.
The stand-alone dust collector is a powerful 135 CFM unit that efficiently separates and traps dust and worn abrasive.
The cabinet design follows the contours of your natural position while sandcarving, which allows you to work comfortably and more productively.
The system is built to last for years, with total seam-welded, 14 gauge steel construction and a epoxy powder-coated finish. The epoxy powder-coated finish resists rust as well as chips, scratches and wears better than other types of finishes.
The large gloveless sleeves are made of a lightweight polyurethane, for easy mobility and handling of your products while sandcarving.
The padded arm rests prevent stress to your forearms and provide added comfort while sandcarving.
The single recessed halogen lighting provides the brightest lit sandcarving workspace on the market. The halogen light also ensures longer life and clean white light during operation.
The oversized laminated safety glass provides superior visibility while sandcarving. The oversized viewing window can easily be replaced.
The full size single door entry is generous in size and opens on the right side of the cabinet. A large entry area minimizes the potential for bumping or nicking your sandcarvrd products.
Locking wheels give you the flexibility to move your system when required.
This footswitch valve provides longer performance and is very low maintenance in comparison to the former footswitch valve. It also optimizes air and sand flow to your hoses.
The 10 ft. heavy duty hose is flexible and provides adequate sand flow and longer blasting usage.
The blasting hose can be used from the right or left side, so the system is as convenient for left-handed sandcarvers as it is for right-handed sandcarvers.
The durable 3/32-inch carbide nozzle is versatile and easy to use for any sandcarving project. It comes with an adapter and O-ring.
This unit regulates the amount of air pressure and sand flow (PSI) being sent to your blasting hose/nozzle and efficiently separates the water content. We have combined the two functions into one unit to minimize space. Standard features include an auto-relieving moisture drain to remove water drops and oil from compressed air, a push-down locking adjustment knob to change pressure settings, pressure gauge, liquid level indicator and manual relieving valve.
The Exclusive "Max Flow" Air Curtain directs air across your viewing window to remove dust and ensure maximum visibility while sandcarving. This process is made possible by a vent above the viewing window. It also, helps prevent dust and overspray to your viewing window.
Rayzist guarantees that our sandcarving systems are built to last.
Leasing Options Available
Price includes:
1- 50lb. bag of Aluminum Oxide 150 grit and standard features, no upgrades necessary.
All Pricing is Subject to Change Without Notice
Why does my footswitch have air blowing out of it when I am not stepping on it?
The problem lies in the Foot Pedal Actuator; here are three things you can check:
I can't get the air to stop coming out my hose. The foot pedal has no control. I have taken apart my entire assembly at the bottom of the pot, replaced the white block along with the rubber diaphragm.
This could only be caused by two possible problems:
1. Air-supply. The Pressure Pot requires at least 80psi supplied to the pot for the diaphragm to stop the flow of air and sand through the white valve body (lower media valve). The upper media valve requires a minimum 30psi greater pressure then your blasting pressure (shown on pot's regulator). The upper media valve receives the unregulated air-supply from the compressor. Confirm your Air Compressor is set at the maximum air-output there should be no air restriction to the pot.
2. Foot Pedal Actuator. There is an actuator located in your foot pedal housing that interrupts the air supply when stepping on the pedal. When the pedal is not being depressed it is "normally open" meaning the air is flowing through it. Once you step on the pedal it allows the built up pressure in the lower media valve to force the diaphragm open and the sand and air to flow through the lower media valve and the blasting hose. If your sand and air is not stopping, possibly the foot pedal actuator is stuck closed or pressed in and will not spring back out. Open the foot pedal housing and confirm the actuator tab springs in and out when pressing the tab.
Does the exhaust vent on the 2034VX and 2648VX need to be vented outside?
No, the exhaust vent on the dust collector does not need to be vented outside; the dust collector does a superb job of collecting the dust and exhausting clear air. However, it is optional to install some flex tubing and exhaust to an outside wall.
Will the 2034VX Sandcarving Systems fit through my shop door?
The 2034VX Sandcarving System will fit through any standard size 36" door. If you have a smaller door entry, as an option, you can remove the padded arm rests; this will reduce the width of the sandcarving system to about 32" allowing for an easier entrance.
And so, dear brothers and sisters, we can boldly enter heaven’s Most Holy Place because of the blood of Jesus. By his death, Jesus opened a new and life-giving way through the curtain into the Most Holy Place. And since we have a great High Priest who rules over God’s house, let us go right into the presence of God with sincere hearts fully trusting him. For our guilty consciences have been sprinkled with Christ’s blood to make us clean, and our bodies have been washed with pure water. Let us hold tightly without wavering to the hope we affirm, for God can be trusted to keep his promise. Hebrews 10:19-23 (NLT)
© Copyright 1997-2018 Rayzist Photomask, Inc. All rights reserved.