LazerMask
  • Why to Buy
  • Product Profile
  • Pricing
  • Order Form
  • Instructionals
  • FAQ's

LazerMask™ Overview

LazerMask™ is specifically designed for shops with both a Laser Engraver and a Sandcarving Cabinet. With LazerMask™ you are able to leverage accuracy of the laser along with the depth of the sandcarving process This is truly the best of both worlds in one easy process.

  • LazerMask™ is a sand resist film, unlike polyester based films used today
  • LazerMask™ is unique water based sand resist unlike anything on the market today
  • LazerMask™ does not contain PVC which will corrode the lasers hardware like vinyl's or rubber resists
  • LazerMask™ has the same resistant qualities as photoresist film
  • LazerMask™ is a translucent color made for easy alignment
  • LazerMask™ is flexible and pliable for easy application to curved surfaces
  • LazerMask™ burns clean and quickly
  • LazerMask™ easily achieves paint fill depths

Description:

LazerMask™ is a non-PVC sandcarving film that won’t corrode your laser’s hardware. With LazerMask™ you can utilize the accuracy and precision of a laser engraver to reproduce images into glass, crystal, and stone while retaining the beauty and depth of traditional sandcarving.

Requirements:

To use LazerMask™ sandcarving film, you need a laser engraver and a sandcarving system similar to our 1924 or 2034VX production models. (Visit www.rayzist.com for more information on sandcarving units).

Durability:

LazerMask™ has blast resilient properties equal to Rayzist’s photoresist films.

Shelf Life:

Non-Applicable. Store at room temperature. No special handling required.

Productivity:

LazerMask™ eliminates the steps of a traditional photomask. Just apply, laser, and sandcarve; a major benefit for small production runs. Blast high resolution designs quickly and easily saving time in application, burn time and clean up.

Material Chosen and Why:

LazerMask™ is a non-PVC sandcarving film offering a fast burn, great detail, durability, with a fast and easy clean up... without the need for sticky, hard to use vinyls or tapes.

LazerMask™ Laser Engraving Film - 200' Rolls

All Pricing is Subject to Change Without Notice

Code

LM4R
LM6R
LM8R
LM10R

Size

4" x 200'

6" x 200'

8" x 200'

10" x 200'

Total sq in

9,600

14,400

19,200

24,000

Price

$144.00

$216.00

$288.00

$360.00

Sq in Price

$.015

$.015

$.015

$.015

To Use:

  1. Apply LazerMask™ to the flat surface of the item beginning at one end burnishing flat with a plastic squeegee to the opposite end(similar to applying vinyl) to avoid trapped air.
  2. Remove the Clear Carrier Film.
  3. Laser the image.
  4. Sandcarve the item.
  5. Paint fill (if desired) while the mask is still on.

Laser Guidelines:

Wattage and resolution settings will effect laser burning times, results may vary.

Low wattage Lasers - 25-35 watt 45-65% Speed x 100% Power

Mid – High wattage Lasers - 40-80 watt 80% Speed x 70-100% Power

Apply

 

Recommended Supplies:

Plastic burnisher: a hand-held, plastic tool used to bind the photomask to the substrate surface and remove the clear carrier sheet from photomask. To use, sweep the burnisher over the applied photomask while applying gentle pressure.

How do you wrap the laser mask on a round or curved surface?

Applying a flat mask to a rounded surface will naturally create some wrinkles.

What I typically do with curvature items is:

  • Separate the plastic backing from your LaserMask material you are going to use, this will eliminate the non-flexible component and give you a little more flexiblity to work with.
  • Apply the flexible LaserMask to your substrate.
  •  With your thumbs work out any wrinkles.

Call 800-729-9478 and place your order!
Call 800-729-9478 and place your order!