Stock Designs | Premade Sandcarving Stencils | Ready to Use Artwork for Sandblasting

Rayzist Photomask Stock Design Catalog

Item #	Size	Price
SCN001-C	5.25 x 4.00	$1.50
SCN001-E	6.75 x 5.00	$2.50
SCN001-G	8.00 x 6.00	$3.50

Item #	Size	Price
SCN002-D	5.00 x 5.25	$2.00
SCN002-G	6.50 x 7.00	$3.50
SCN002-J	8.00 x 8.25	$5.00

Item #	Size	Price
SCN003-D	5.25 x 4.25	$2.00
SCN003-F	6.75 x 5.50	$3.00
SCN003-H	8.25 x 7.00	$4.00

Item #	Size	Price
SCN004-C	4.00 x 5.50	$1.50
SCN004-E	5.00 x 7.25	$2.50
SCN004-H	6.50 x 8.00	$4.00

Item #	Size	Price
SCN005-A	4.75 x 1.50	$0.50
SCN005-B	6.50 x 2.00	$1.00
SCN005-C	8.00 x 2.50	$1.50

Item #	Size	Price
SCN006-E	5.00 x 6.25	$2.50
SCN006-G	6.00 x 7.50	$3.50
SCN006-J	7.25 x 9.50	$5.00

Item #	Size	Price
SCN007-C	5.25 x 3.25	$1.50
SCN007-E	7.00 x 4.50	$2.50
SCN007-F	8.00 x 5.00	$3.00

Item #	Size	Price
SCN008-A	3.75 x 1.75	$0.50
SCN008-B	4.00 x 2.00	$1.00
SCN008-C	4.25 x 3.00	$1.50

Item #	Size	Price
SCN009-B	3.00 x 3.00	$1.00
SCN009-C	4.00 x 4.00	$1.50
SCN009-D	5.00 x 5.00	$2.00

Item #	Size	Price
SCN010-A	2.00 x 2.50	$0.50
SCN010-B	2.50 x 3.00	$1.00
SCN010-C	3.00 x 3.50	$1.50

Item #	Size	Price
SCN011-B	3.50 x 3.00	$1.00
SCN011-C	4.25 x 3.50	$1.50
SCN011-D	5.25 x 4.50	$2.00

Order Form

Recommended Stock Design Supplies

Rayzist offers a full line of products designed to optimize the performance of your Stock Designs. The recommended supplies for use with these films are shown below.

Plastic burnisher: a hand-held, plastic tool used to bind the photomask to the substrate surface and remove the clear carrier sheet from photomask. To use, sweep the burnisher over the applied photomask while applying gentle pressure.
Blasting tape: a ribbed vinyl tape that is used to protect areas of the substrate that are not covered by the photomask. A quality blasting tape is easy to tear, very durable, and peels away from the substrate without leaving a sticky or gummy residue behind.
Wire wheel brush: a hand-held brush tool used to release air trapped between the photomask membrane and the substrate surface. The brush is equipped with a handle for ease-of-use and hairline bristle wire for gentle perforation of the photomask membrane. It is used after the photomask is burnished to the substrate surface.